Volt Edge has now developed a National Recognised Inspectors course, which is a course designed to allow a Hazardous Area Electrician to:
→ Be authorised at a particular site as an Inspector.
→ Used as technical back up for the QLD Hazardous Areas Auditors application.
OR
→ Used at technical back up for the Victorian H class inspectors course and application.
This is a 5 day course via our Live Web Training. The person, when deemed competent, should be able to inspect previous completed a detailed inspection of a hazardous area installation and then create an auditable document list of non compliances and which clause in the Australian Standards that is required. Available in Brisbane only.
After successful completion of this course, students will have the skills to:
→ Verify hazardous classification for the area.
→ Select and check equipment, wiring and accessories.
→ Design system and installation.
→ Audit hazardous areas documentation (verification dossier).
→ Prepare to audit as-built installation.
→ Establish and implement procedures for maintaining explosion-protection.
Learn to compile, manage and assess a Hazardous Area Verification Dossier against the requirements
Pair workplace protocols and creative initiative to methodically design and produce various projects
Compile and produce appropriate documentation of work operations.
Learn to document, compile and report audit findings. Upskill and become a QA/QC specialist.
| Unit Code | Unit Name |
|---|---|
| UEENEEM054A | Plan Electrical installations of hazardous areas – gas. |
| UEENEEM056A | Plan Electrical installations of hazardous areas – pressurisation. |
| UEENEEM057A | Design explosion-protected electrical systems and installations – gas. |
| UEENEEM059A | Design explosion-protected electrical systems and installations – pressurisation. |
| UEENEEM065A | Conduct audit of hazardous areas installations – gas atmospheres. |
| UEENEEM078A | Manage compliance of hazardous areas. |
Pre-requisites
Electrical Engineering Degree holders must provide: Copy of Transcript from Degree, your current resume and an detailed overview of examples of the below that you have undertaken, this can be in the form of work samples or if not available written summary of the work. Must be able to demonstrate:
• Design specifications and scope
• Designing and Planning of Electrical Installations
Students who do not meet the pre-requisite requirements and still undertake the course can gain a statement of completion (non-accredited outcome)
UEENEEM054A Plan Electrical installations of hazardous areas – gas
Pre-Requisites
Granting competency in this unit shall be made after or concurrently with confirming competency in any one of the following units:
UEENEEM024A Install explosion-protected equipment and wiring systems gas atmospheres
OR
Competencies in planning general electrical/instrumentation installations at AQF4 or equivalent. Examples are (but not limited to):
UEENEEG125A Plan electrical installations with a low voltage demand up to 400 A per phase
UEENEEI112A Verify compliance and functionality of instrumentation and control installations
EENEEM056A Plan Electrical installations of hazardous areas – pressurisation
Pre-Requisites
Granting competency in this unit shall be made after or concurrently with confirming competency in any one of the following units:
UEENEEM026A Install explosion-protected equipment and wiring systems pressurisation
OR
Competencies in planning general electrical/instrumentation installations at AQF4 or equivalent. Examples are (but not limited to):
UEENEEG125A Plan electrical installations with a low voltage demand up to 400 A per phase
UEENEEI112A Verify compliance and functionality of instrumentation and control installations
UEENEEM057A Design explosion-protected electrical systems and installations – gas
Pre-Requisites
Granting competency in this unit shall be made after confirming competency in designing electrical systems and installations at AQF level 6 or equivalent. Examples are (but not limited to):
UEENEEE115A Develop design briefs for electrotechnology projects
UEENEEG130A Design switchboards rated for high fault levels (greater than 400 A)
UEENEEI123A Design electronic control systems
UEENEEM059A Design explosion-protected electrical systems and installations – pressurisation
Pre-Requisites
UEENEEE015B Develop design briefs for electrotechnology projects
UEENEEG130A Design switchboards rated for high fault levels (greater than 400 A)
UEENEEI123A Design electronic control systems
UEENEEM065A Conduct audit of hazardous areas installations – gas atmospheres
Pre-Requisites
Granting competency in this unit shall be made after or concurrently with confirming competency in engineering auditing/evaluation AQF 5 or equivalent. Examples are (but not limited to):
UEENEEG131A Evaluate performance of low voltage electrical apparatus
OR
UEENEEG060B Evaluate performance of LV electrical machines
UEENEEM078A Manage compliance of hazardous areas
Pre-Requisites
Granting competency in this unit shall be made after or concurrently with confirming competency in general plant management at AQF 4 Example are (but not limited to):
PMASUP410A Develop plant documentation
$ 2,800 (GST Free).
Pre-requisites offered by Volt Edge:
UEENEEE071B Write specifications for electrical engineering projects & UEENEEE015B Develop design briefs for electrotechnology projects: $350.00
Develop Plant Docs: $ 220.00
The course can be done by Engineers or Electricians with a background in Hazardous Areas to be able to inspect other tradesmen’s hazardous area work to Australian Standards.
Knowledge of an Australia Standards is important, although the student will receive particular information from the below standards:
→ AS/NZS 60079.14:2017 Part14 Design selection, erection and initial inspection.
→ AS/NZS 3000 2018 Wiring Rules.
Complete your details below to have a chat with our course advisor.
Enquire now
